1. Harshal Kulkarni, Carl Blais, Vikram V. Dabhade, “Analysis of machining a sinter-hardened powder-metallurgy-steel: Significance of localised densification of uncut-chip-material during chip formation,” Materials Engineering and Performance, (2024) Accepted

2. S. K. Rajulapati, Lekhraj Verma, Himanshu Pal, Vikram V. Dabhade, Ujjwal Prakash, “Effect of yttria content on microstructural evolution, mechanical properties and temperature dependent strengthening mechanisms in 9Cr-oxide dispersion strengthened (ODS) steel developed by hot powder forging,” Materials Today Communications, Vol. 40 (2024) 109661

3. Indeevar Singh, Vikram V. Dabhade, “Tungsten heavy alloys for kinetic energy penetrators: a review” Materials Science and Technology, (2024) Accepted

4. Polasani Ajay, S.D. Gaikwad, , Vikram V. Dabhade, S.V.S.Narayana Murty, Sushant Manwatkar “Dissolution studies during the mechanical alloying of Inconel-718 superalloy based elemental powders,” Materials Today Communications, Vol. 39, (2024), 109275

5. Lekhraj Verma, Vikram V. Dabhade, “Grain Coarsening Kinetics and Mechanical Properties of Fe-15Cr-2W ODS Steels with varying Yttria contents,” Powder Metallurgy and Metal Ceramics, (2024), Accepted.

6. Tilak Joshi, Sanjay Rathore, Vikram V. Dabhade and Ujjwal Prakash, “Dry Sliding Wear Behavior of Sinter Forged Micrometric and Nanometric Yttrium Oxide Reinforced AA-7075 Matrix Composites,” Journal of Alloys and Metallurgical Systems, Vol. 6, (2024) 100067

7. S.D. Gaikwad, Vikram V. Dabhade, S.V.S. Narayana Murty, Sushant Manwatkar, Mechanical alloying and direct powder forging of Ni–20Cr–20Fe-0.08C alloy, Materials Chemistry and Physics, 315 (2024) 129039

8. S.D. Gaikwad, Polasani Ajay, Vikram V. Dabhade, S.V.S.Narayana Murty, Sushant Manwatkar , U. Prakash, “Mechanical properties and microstructural analysis of ultra-fine grained Ni-based ODS alloy processed by powder forging,” Journal of Alloys and Compounds, 970 (2024) 172614

9. S.D. Gaikwad, Vikram V. Dabhade, S.V.S. Narayana Murty, Sushant Manwatkar, “Studies on alloying process of Ni-20Cr-20Fe-0.6Y2O3 powders during mechanical alloying,” Powder Technology, 433 (2024) 119171

10. Lekhraj Verma and Vikram V. Dabhade, Grain growth kinetics and mechanical properties of spark plasma sintered Fe-15Cr-2W powders, Materials Today Communication, 37 (2023) 107568

11. Harshal Kulkarni, Vikram V. Dabhade, “Machinability of a sinter-hardened powder metallurgy steel: A combined analysis of cutting force and chip characteristics”, Powder Metallurgy and Metal Ceramics, Vol. 62, Nos. 7-8, November, 2023

12. Sunil Kumar Rajulapati , S.D. Gaikwad, Vikram V. Dabhade, Ujjwal Prakash,” Effect of directional anisotropy on mechanical properties of 9Cr Ferritic/ Martensitic ODS steels processed by mechanical alloying and powder forging,” Materials Today Communication, Vol. 37, 2023, 107220

13. Harshal Kulkarni, Vikram V. Dabhade, “Machining pre-sintered compacts of a sinter-hardenable powder metallurgy steel: A novel methodology for selecting sintering temperatures for the optimum machinability”, Journal of manufacturing processes, (2023) Vol. 105, 444-462

14. Lekhraj Verma and Vikram V. Dabhade, “Synthesis of Fe-15Cr-2W Oxide Dispersion Strengthened (ODS) Steel Powders by Mechanical Alloying”, Powder Technology, (2023), Vol. 425, 118554

15. Harshal Kulkarni, Vikram V. Dabhade and Carl Blais, “Analysis of machining green compacts of a sinter-hardenable powder metallurgy steel: A perspective of material removal mechanism”, Journal of Manufacturing Science and Technology (2023), Vol. 41, April 2023, 430-445

16. Tialk Joshi, Harshal Kulkarni, Vikram V. Dabhade and Ujjwal Prakash, “Influence of Nanometric and Micrometric Reinforcement on Machining of Powder-Forged Al-7075/Y₂O₃ Composites” Journal of Materials Engineering and Performance (2022), Vol. 32, 6496–6507

17. Rathore S.S, Singh M.K, Joshi T.C, Dabhade V.V., “Homogenization Study of Molybdenum and Copper in P/M Steel”, Journal of Engineering Research, (2022),Vol. 10, 95-105

·         D. Kumar, R. Singh, U. Prakash, V. V. Dabhade, “Reducing Anisotropy in High Yttria Ferritic Oxide Dispersion Strengthened Steels by Powder Forging” K. Laha & T. Sakthivel, Journal of Materials Engineering and Performance, Vol. 31, (2022) 994–1002

·          

18. S. K. Chaurasia, Vikram V. Dabhade, Ujjwal Prakash and S. K. Nath “Effect of Carbon Addition on Mechanical Properties and Dry Sliding Behavior of Fe-0.65P Alloy Processed by Powder Forging” Transactions of the Indian Institute of  Metals (2021) 74(3), 735-742

19. A. Malakar, V. Pancholi, and V.V. Dabhade, “Recrystallization and Strengthening Mechanism in Friction-Stir-Processed Al Powder Compacts”, Journal of Materials Engineering and Performance, Vol. 29(5),   (2020) 3243–3252.

20. Vinay R. Kulkarni, Jagannath Nayak, and Vikram V. Dabhade, “Effect Of Heat Treatment On Properties Of Sinter Forged Fe-Cu-C-Cr Steel,” Journal of Mechanical Engineering Research and Developments, (2019), 42(4), 225-277

21. Harshal Kulkarni and Vikram V. Dabhade, “Green machining of powder-metallurgy-steels (PMS): An overview”, Journal of manufacturing processes, 44 (2019),1-18.

22. D. Kumar, U. Prakash, V.V. Dabhade, K. Laha, and T. Sakthivel, “Mechanical Alloying and Powder Forging of 18%Cr Oxide Dispersion-Strengthened Steel Produced Using Elemental Powders,” Journal of Materials Engineering and Performance, Vol.28, (2019) 242-253

23. Harshal Kulkarni and Vikram V. Dabhade, “Influence of MnS in processing and applications of Sintered Fe-Cu-C Alloys: An Overview,” Materials Today Proceedings 5 (2018) 17277-17283

24. D. Kumar, U. Prakash, V.V. Dabhade, K. Laha, and T. Sakthivel, Influence of Yttria on Oxide Dispersion Strengthened (ODS) Ferritic Steel, Materials Today: Proceedings, 5 (2018) 3909–3913

25. S.K. Chaurasia, U. Prakash, Vikram Dabhade, S.K. Nath, Dry Sliding Wear of Fe Based Powder Processed Through Hot Powder Forging Technique, Materials Today: Proceedings, 5 (2018) 17170–17179

26. Vinay R. Kulkarni, Jagannath Nayak and Vikram V. Dabhade, “Effect of chromium addition on properties of sinter-forged Fe Cu C alloy steel,” International Journal of Modern Physics B, Vol. 32, No. 19 (2018)

27. Sanjay S. Rathore, Vikas Verma, B.V. Manoj Kumar, Vikram V. Dabhade, “Tribological behaviour of sinter-forged Fe-2Cu-0.7C-xMo alloys,” Wear, 410–411 (2018) 222–231

28. S. K. Chaurasia, Ujjwal Prakash, Vikram Dabhade & S. K. Nath “Effect of Phosphorus Addition on Dry Sliding Behavior of Fe–P Alloys Prepared by Powder Metallurgy” Metallography, Microstructure, and Analysis, Vol.7,  (2018) 347–355

29. Y. Mehta, Rajput S K, Chaudhari G P and Dabhade V V, Microstructural evolution in Fe-0.13P-0.05C steel during compression at elevated temperatures IOP Conference Series: Mater. Sci. Eng. Vol. 330,  012005

30. Y. Mehta, Rajput S K, Chaudhari G P and Dabhade V V, “A study on chloride induced depassivation of Fe-P-C-Si and Fe-P-C-Si-N steels in simulated concrete pore solution” IOP Conf. Series: Mater. Sci. Eng. Vol. 330, 012014

31. Yashwant Mehta, S.K. Rajput, Gajanan P. Chaudhari, Vikram V. Dabhade, “Dynamic recrystallization and grain refinement of Fe-P-C-Si and Fe-P-C-Si-N steels”, Journal of Materials Engineering and Performance, Vol. 27, (2018), 4770-4782.

32. Chaurasia S.K., Prakash U., Dabhade V., Effect of Phosphorus on Microstructure and Mechanical Properties of Iron-Based Alloys Processed Through Powder Forging, Metallography, Microstructure, and Analysis December 2017, Volume 6, Issue 6, pp 561–568

33. Deepak Kumar, Ujjwal Prakash, Vikram V. Dabhade, K. Laha, T. Sakthivel, “High yttria ferritic ODS steels through powder forging” Journal of Nuclear Materials, 488 (2017) 75-82

34. Deepak Kumar, Ujjwal Prakash, Vikram V. Dabhade, K. Laha, and T. Sakthivel, “Development of Oxide Dispersion Strengthened (ODS) Ferritic Steel Through Powder Forging” Journal of Materials Engineering and Performance, Vol. 26(4), (2017), 1817-1824

35. Mishra D.D., Makkar P., Rath P.K., Dabhade V.V., Agarwala V., Agarwala R.C., Effect of Ti Particle Size on the Reaction Kinetics and Densification of TiAl Intermetallics, Transactions of the Indian Institute of  Metals (2017) 70(1):175–185

36. Tilak C. Joshi, Ujjwal Prakash, Vikram V. Dabhade, Effect of Nano-Scale and Micro-Scale Yttria Reinforcement on Powder Forged AA-7075 Composites, Journal of Materials Engineering and Performance Volume 25(5) May, (2016)1889-1902

37. Yashwant Mehta, Vikram V. Dabhade, Gajanan P. Chaudhari, “Effect of silicon and nitrogen on the microstructure and mechanical behaviour of high-phosphorous steels,” Metallography, Microstructure and Analysis, Vol. 5, Issue 5, (2016) pp 384-391

38. Yashwant Mehta, S.K. Rajput, Vikram V. Dabhade, and G.P. Chaudhari, “Physical Simulation of Hot Deformation and Microstructural Evolution of Fe-0.05C-0.13P Steel,” Journal of Materials Engineering and Performance, Vol. 25, Issue 4, (2016) pp 1376-1383

39. S. K. Rajulapati, U. Prakash, K. Laha, and Vikram V. Dabhade, “Studies on alloying process of a ferritic/martensitic oxide dispersion strengthened (ODS) steel prepared by mechanical alloying of elemental powders” Powder Metallurgy, Vol. 59 (5), (2016), pp.350-358.

40. Sanjay S. Rathore and Vikram V. Dabhade “Hardenability of Sinter-Forged Fe-2Cu-0.7C-xMo Alloys” Journal of Alloys and Compounds, Volume 664, (2016), 133-140.

41. Sanjay S. Rathore and Vikram V. Dabhade “Dimensional Change during Sintering of Fe-Cu-C Alloys - A Comparative Study ” Transactions of the Indian Institute of Metals, July, (2015)

§

      42. Y. Mehta, V.V. Dabhade, G.P. Chaudhari, Metallography of Fe-P-C and Fe-P-C-Si-N alloys, Metallography, Microstructure, and Analysis 4 (2015) 488-496.

43. Sanjay S Rathore, Milind M Salve and Vikram V. Dabhade “Effect of Molybdenum addition on Mechanical Properties of Sinter-Forged Fe-Cu-C Alloys” Journal of Alloys and Compounds, Volume 649, November 2015, 988-995.

44. Tilak C. Joshi, Ujjwal Prakash, Vikram V. Dabhade, “Microstructural development during hot forging of Al 7075 powder” Journal of Alloys and Compounds, Volume 639, 5 August 2015, Pages 123-130.

45. D.D. Mishra, V.V. Dabhade, V. Agarwala and R.C. Agarwala, “Effect of Al particle size on the reaction kinetics and densification of TiAl intermetallics”, Phase Transitions, 2014, Vol. 87, No. 4, 344–356. 

46. Jung Ju Kim, Hyo Won Lee, V.V. Dabhade, Soo Ryong Kim and Woo Teck Kwon, Doo Jin Choi, Hyungsun Kim and Younghee Kim, “Electromagnetic Interference Shielding Characteristic of Silver Coated Copper Powder,” Metals and Materials International, 16, 3 (2010) 469-475.

47. V.V. Dabhade, T.R. Rama Mohan, “Effect of external energy on the atomic, crystalline, and powder characteristics of antimony and bismuth powders,” Bulletin of Materials Science, 32, 5 (2009) 471-479.

48. K. Song, V.V. Dabhade, W.Z. Misiolek, “Mixing studies of aluminum and CNT powders in the process of  nanocomposite fabrication,” Steel Research International, 79, vol. 2, 2008, 563 – 569

49. V.V. Dabhade, P. Kansuwan and W.Z. Misiolek, “Consolidation of Aluminum powder during extrusion,”   International Journal of Powder Metallurgy, 44, 4 (2008) 27-36.

50. V.V. Dabhade, T.R. Rama Mohan and P.  Ramakrishnan, “Sintering bahavior of Titanium-Titanium Nitride Nanocomposite powders,” Journal of Alloys and Compounds, 453 (2008) 215-221.

51. V.V. Dabhade, T.R. Rama Mohan and P. Ramakrishnan, “Initial sintering kinetics of attrition milled  nanocrystalline titanium powders,” Materials Science and Engineering. A, 452-453 (2007) 386-394.

52. V.V. Dabhade, T.R. Rama Mohan and P. Ramakrishnan, “Dilatometric sintering study of titanium-titanium nitride nano / nanocomposite powders,” Powder Metallurgy, 50, 1 (2007) 33-39.

53. V.V. Dabhade, T.R. Rama Mohan and P. Ramakrishnan, “Viscous flow during sintering of attrition milled  nanocrystalline titanium powders,” Materials Research Bulletin, 42, 7 (2007) 1262-1268.

54. V.V. Dabhade, T.R. Rama Mohan and P.  Ramakrishnan, “Initial sintering kinetics of titanium-titanium nitride nano / nanocomposite powders,” Powder Metallurgy, 50, 2 (2007) 157-164.

55. Y.H. Kim, S.R. Kim, B.G. Song, V.V. Dabhade, B.K. Sea and W.T. Kwon, “Nanoporous SiC membranes derived from preceramic polymer,” Solid State Phenomena, 124-126 (2007) 1733-1736.

56. Hyun-Jung Park, V.V. Dabhade,  Kyungja Kim, Soo-Ryong Kim, Woo-Tech Kwon and Younghee Kim,  “Hydrothermal synthesis of hydroxyapatite powders using alkyl ammonium bromides as surfactants,” Key  Engineering Materials 342-343 (2007) 873-876.

57. W.T. Kwon, S.R. Kim, Y. Kim, J.H Hwang, V.V. Dabhade, T.W. Yoo and S.Y. Bae, “Characterization of  automobile shredder residues for chlorine content and estimation of it’ circulation in cement kiln” Materials Science Forum, 544-545 (2007) 681-684.

58. V.V. Dabhade, B.B. Panigrahi, M.M. Godkhindi, T.R. Rama Mohan and P.  Ramakrishnan, “Dilatometry of attrition milled nanocrystalline titanium Powders,” Materials Research Bulletin, 41, 11 (2006) 2111-2122.

59. V.V. Dabhade, T.R. Rama Mohan and P. Ramakrishnan, “Nanocrystalline titanium powders by high energy  attrition milling,” Powder Technology, 171, 3 (2006) 177-183.

60. B.B. Panigrahi, M. M. Godkhindi, K. Das, P.G. Mukunda, V.V. Dabhade and P. Ramakrishnan "Sintering mechanisms of attrition milled titanium nano powder," Journal of  Materials Research, 20, 4 (2005) 827-836.

61. B.B. Panigrahi, V.V. Dabhade, M.M. Godkhindi, “Thermal expansion behavior of micro and nano titanium powder compacts,” Materials Letters, 59, 19-20 (2005) 2439-2541.

62. V.V. Dabhade, T.R. Rama Mohan and P. Ramakrishnan, "Synthesis of nanosized titanium powder by high  energy milling," Applied Surface Science, 182, 3-4 (2001) 390-393.